HCR1450-EDII Rock Drill – Continuously adapts to the changing rock conditions, increasing drilling performance and the life of drill tools while decreasing fuel consumption.

The HCR1450-EDII with extendable boom incorporates a self-adjusting drill system that ensures high productivity no matter what the drilling situation.

Low-emission Tier IV engines offer low fuel consumption and meets US exhaust emissions regulations.

The Furukawa HD828S drifter combines powerful penetration with agility and easy operation. Equipped with features that maximize efficiency, the HD828S drifter sets the standard in high-performance drilling.

Features & Benefits

HCR1450-EDII Tier-IV Rock Drill

HCR1450-EDII Features & Benefits

  • Advanced rotary rod changer allows easy drill rod changes. Operators can add and remove rods using a single lever.
  • HCR1450-EDII features 12′ rods with extendable boom for increased drill pattern.
  • Heavy-duty undercarriage – featuring a pentagonal section design to reduce dirt build-up and track wear – ensures strength and durability.
  • High-output compressor increases flushing air, provides faster drilling and decreases bit wear.
  • Reliable dust control system increases suction capacity and provides effective pre-cleaner to reduce escape of drilling dust. An optional dust suppression system is available for difficult drilling conditions.
Specifications

HCR1450-EDII Specifications

 HCR1450-ED Series II
PERFORMANCESUS StandardMetric
Operating Weight with Fuel/Oil36,288 lbs.16,460 kg
Travel Speed0-2.3 mph0-3.7 km/h
Maximum Traction Force22,144 lb-force98.5 kN
Maximum Grade of Hill Climb57.7% (30˚)
Oscillating Angle+-8.5 deg
Ground Contact Pressure12.8 psi87.9 kPa
DRIFTER
ModelHD828S
Operating Weight533 lbs.242 kg.
Mass597 Ibs.271 kg
Overall Length3'10"1,158 mm
Overall Width1'4"387.4 mm
Overall Height1'1"327.5 mm
Number of Blows2,500~3,000 bpm2,500~3,000 min-1
Number of Revolutions0-190 rpm0-190 min-1
ENGINE
Make & ModelCummins QSB6.7 (Tier4 Final, Stage IV)
TypeWater-cooled Direct Fuel Injection Turbo Charged Diesel Engine
Rated Output260 hp/2,500 rpm194 kw/2,500 min-1
HYDRAULIC EQUIPMENT
Variable Displacement PumpAxial Piston Pump X2
Fixed Displacement PumpGear Pump X3
Drive MotorHydraulic Motor with Reduction Gear
BOOM
ModelJE326-134
TypeExtension Boom
Boom Lifting Angle: Up/Down41˚/20˚
Boom Swing Angle: Right/Left32˚/5˚
Boom Slide Length2'11"900 mm
GUIDE SHELL
ModelGH832-33
Overall Length28'6"8,700 mm
Feed Length15'1"4,595 mm
Guide Slide Length4'11"1,500 mm
Guide Swing Angle: Right/Left25˚/90˚
Guide Tilt Angle170°
Maximum Pulling Force7,644 lb-force34 kN
Feed SystemHydraulic Motor Drive
COMPRESSOR
Make & ModelAIR MAN, PDS265-S37F
TypeScrew 1-Stage
Discharge Airflow353 CFM10.0 m3/min
Discharge Pressure149 psi1.03 MPa
DUST COLLECTOR
ModelA885-44
Airflow1,413 CFM40 m3/min
Number of Elements6
Dust Removal SystemAutomatic Pulse Air Jet
Suction CapSlide Type
ROD CHANGER
Number of Rods7
Rod Length T38 - T4512'3,660 mm
ELECTRICAL EQUIPMENT
Battery12V; 108Ah/5Hr
VoltageDC24V
FUEL/OIL CAPACITY
Fuel Tank112 gal425 L
Hydraulic Tank57 gal215 L
DEF
DEF Capacity5 gal19 L
BIT AND ROD
Bit Diameter3" - 5"76 - 127 mm
Bit ProfileButton, Cross and Spike
Rod Size45R, 51R
Rod Length12'3,660 mm
First Rod Length Maximum14'4,265 mm
CIRCUMSTANCE
Working Temperature5° – 113° F-15° – +45° C
Maximum AltitudeMax. 8,202 ftMax. 2,500 m
The contents of these specifications are subject to change without notice.
CUMMINS is a registered trademark of Cummins, Inc.
Dimensional Information

Drilling Coverage – Printable PDF

 

Front View – Printable PDF

End View – Printable PDF

Options

HCR1450-EDII Options

OPTIONAVAILABILITY
Water/dust suppression system
Remote control
Rod setter
Heavy-duty rear-mounted bumper
Cold start kit (ESPAR, WEBASTO)
2D angle indicator
3D angle indicator
Drill monitoring system with GPS capabilities
Heating pad
Handrails
Central greasing system
Tropical kit
Rear view camera